產品資訊

• 1-T 80C51 Central Processing Unit
• MG82FG5A32 with 32K Bytes flash ROM
  • ISP memory zone could be optioned as 1KB/1.5KB~4KB
  • Flexible IAP size by software configured
  • Code protection for flash memory access
  • Flash erase/program cycle: 10,000 times
  • Flash data retention: 100 years at 25℃
  • Default MG82FG5A32 Flash space mapping

    AP Flash mapping	32KB 0000h~7FFFh
    IAP Flash mapping	30.5KB 8000h~F9FFh
    ISP Flash mapping	1.5KB FA00h~FFFFh,ISP Boot code

• Data RAM
  • On-chip 256 bytes scratch-pad RAM
  • 5120 bytes expanded RAM (XRAM)
•  Dual data pointer
• Variable length MOVX for slow SRAM/Peripherals
• Interrupt controller
  • 16 sources, four-level-priority interrupt capability
  • Four external interrupt inputs, nINT0, nINT1, nINT2 and nINT3
  • All external interrupts support High/Low level or Rising/Falling edge trigger
• Four 16-bit timer/counters, Timer 0, Timer 1, Timer 2 and Timer 3
  • T0CKO on P34, T1CKO on P35, T2CKO on P10 and T3CKO on P01
  • X12 mode enabled for T0/T1/T2/T3
• Programmable 16-bit counter/timer Array (PCA) with 6 compare/capture modules
  • Capture mode
  • 16-bit software timer mode
  • High speed output mode
  • 8/10/12/16-bit PWM (Pulse Width Modulator) mode with phase shift function
• Keypad Interrupt (P0/P2/P5/P6)
• 12-Bit ADC
  • Programmable throughput up to 250 ksps
  • Up to 8 channel single-ended inputs or 4 channel differential inputs
• Enhanced UART (S0)
  • Framing Error Detection
  • Automatic Address Recognition
  • Speed improvement mechanism (X2/X4 mode)
• Secondary UART (S1)
  • Dedicated Baud Rate Generator
  • S1 shares baud rate generator to S0
• Master/Slave SPI serial interface
• Master/Slave two wire serial interface (TWSI)
• Programmable Watchdog Timer, clock sourced from ILRCO
  • One time enabled by CPU or power-on
  • Interrupt CPU or Reset CPU on WDT overflow
  • Support WDT function in power down mode (watch mode)
• On-Chip-Debug interface (OCD)
• Maximum 55 GPIOs in LQFP64 package
  • P3 can be configured to quasi-bidirectional, push-pull output, open-drain output and input only
  • P0, P1, P2, P4, P5 and P6 can be configured to open-drain output or push-pull output
  • P6.0 and P6.1 shared with XTAL2 and XTAL1
• Multiple power control modes: idle mode, power-down mode, slow mode, sub-clock mode, watch mode and monitor mode.
  • All interrupts can wake up IDLE mode
  • 11 sources to wake up Power-Down mode
  • Slow mode and sub-clock mode support low speed MCU operation
  • Watch mode supports WDT to resume CPU in power down
  • Monitor mode supports BOD1 to resume CPU in power down
• Two Brown-Out Detectors
  • BOD0: detect 2.2V
  • BOD1: selected detection level on 4.2V/3.7V/2.4V/2.0V
  • Interrupt CPU or reset CPU
  • Wake up CPU in Power-Down mode
• Operating voltage range: 2.0V – 5.5V
  • Minimum 2.2V requirement in flash write operation (ISP/IAP/ICP)
• Operating frequency range: 36MHz(max)
  • External crystal mode, 2 – 12MHz @ 2.0V – 5.5V and 2 – 25MHz @ 2.7V – 5.5V
  • CPU up to 12MHz @ 2.0V – 5.5V, up to 25MHz @ 2.4V – 5.5V and up to 36MHz @ 2.7V – 5.5V
• Clock Sources
  • Internal 11.0592MHz oscillator (IHRCO): factory calibrated to ±1%, typical
  • External crystal mode
  • Internal Low power 32KHz RC Oscillator (ILRCO)
  • External clock input (ECKI) on P6.0/XTAL2, up to 36MHz
  • Internal Oscillator output on P6.0/XTAL2
  • On-chip Clock Multiplier (CKM) to provide high speed clock source
• Operating Temperature:
  • Industrial (-40℃ to +125℃)*

•  Package Types:
  • LQFP48(7 mm*7 mm):MG82FG5A32AD48
  • LQFP64(7 mm*7 mm):MG82FG5A32AD64

Note*: Tested by sampling.